LCR All-in-1 Component Tester Transistor Diode Capacitance ESR Meter Inductance

Sold $13.99 Buy It Now or Best Offer, $2.00 Shipping, 30-Day Returns, eBay Money Back Guarantee
Seller: haiy_95inliao ✉️ (59,748) 0%, Location: hong kong, HK, Ships to: WORLDWIDE, Item: 321511426333 LCR All-in-1 Component Tester Transistor Diode Capacitance ESR Meter Inductance.
Welcome to hylbuy store  

Similar items for sell, pls click!

*************************************** *************************************** *************************************** ************

  

Items details

Feature(The meter updated on June-02, After June-02, will send out new version) ***************************************************************************************** ***************************************

Automatic identify components.

Automatically detect the pins.

Automatic measurement parameters.

As component meter: can measure resistor/ diode/ capacitor/ transistors/ inducitor

As the pulse generator:  square wave/ variable pulse width wave

Packing list:

1 X Component tester

Not include battery(the airmail ban it, the battery type for the meter is 6F22(9v)).

Specifications: For you reference

1.1 Operates with ATmega328 microcontrollers.

1.2 Displaying the results to a 128x64 graphic LCD-Display.

1.3 One key operation with automatic power shutdown.

1.4 Shutdown current is only about 20nA.

1.5 Automatic detection of NPN and PNP bipolar transistors, N- and P-Channel MOSFETs, JFETs, diodes, double diodes, Thyristors and Triacs.

1.6 Automatic detection of pin layout of the detected part.

1.7 Measuring of current ampli?cation factor and Base-Emitter threshold voltage of bipolar transistors.

1.8 Darlington transistors can be identi?ed by the threshold voltage and high current ampli?cation factor.

1.9  Detection of the protection diode of bipolar transistors and MOSFETs.

1.10 Measuring of the Gate threshold voltage and Gate capacity value of MOSFETs.

1.11 Up to two Resistors are measured and shown with symbols and values with up to four decimal digits in the right dimension. All symbols are surrounded by the probe numbers of the Tester (1-3). So Potentiometer can also be measured. If the Potentiometer is adjusted to one of its ends, the Tester cannot di?er the middle pin and the end pin.

1.12 Resolution of resistor measurement is now up to 0.01ohms, values up to 50M ohms are detected.

1.13 One capacitor can be detected and measured. It is shown with symbol and value with up to four decimal digits in the right dimension. The value can be from 25pF  to 100mF. The resolution can be up to 1pF .

1.14 For capacitors with a capacity value above 0.18μF the Equivalent Serial Resistance (ESR) is measured with a resolution of 0.01? and is shown with two signi?cant decimal digits.

1.15 For capacitors with a capacity value above 5000pF the voltage loss after a load pulse can be determined. The voltage loss give a hint for the quality factor of the capacitor.

1.16 Up to two diodes are shown with symbol or symbol in correct order. Additionally the ?ux voltages are shown.

1.17 LED is detected as diode, the ?ux voltage is much higher than normal. Two-in-one LEDs are also detected as two diodes.

1.18 Zener-Diodes can be detected, if reverse break down Voltage is below 4.5V. These are shown as two diodes, you can identify this part only by the voltages. The outer probe numbers, which surround the diode symbols, are identical in this case. You can identify the real Anode of the diode only by the one with break down (threshold) Voltage nearby 700mV!

1.19 If more than 3 diode type parts are detected, the number of founded diodes is shown additionally to the fail message. This can only happen, if Diodes are attached to all three probes and at least one is a Z-Diode. In this case you should only connect two probes and start measurement again, one after the other.

1.20 Measurement of the capacity value of a single diode in reverse direction. Bipolar Transistors can also be analysed, if you connect the Base and only one of Collector or Emitter.

1.21 Only one measurement is needed to ?nd out the connections of a bridge rectier.

1.22 Capacitors with value below 25pF are usually not detectet, but can be measured together with a parallel diode or a parallel capacitor with at least 25pF. In this case you must subtract the capacity value of the parallel connected part.

1.23 For resistors below 2100? also the measurement of inductance will be done. The range will be from about 0.01mH to more than 20H, but the accuracy is not good. The measurement result is only shown with a single component connected.

1.24 Testing time is about two seconds, only capacity or inductance measurement can cause longer period.

1.25 Software can be configured to enable series of measurements before power will be shut down.

1.26 Selectable facility to calibrate the internal port resistance of port output and the zero o?set of capacity measurement with the selftest . A external capacitor with a value between 100nF and 20μF connected to pin 1 and pin 3 is necessary to compensate the o?set voltage of the analog comparator. This can reduce measurement errors of capacitors of up to 40μF. With the same capacitor a correction voltage to the internal reference voltage is found to adjust the gain for ADC measuring with the internal reference.

1.27 Display the Collector cuto? current ICE0 with currentless base (10μA units) and Collector residual current ICES with base hold to emitter level . This values are only shown, if they are not zero (especially for Germanium transistors).

1.28 Thyristors and Triacs can only be detected, if the test current is above the holding current. Some Thyristors and Triacs need as higher gate trigger current, than this Tester can deliver. The available testing current is only about 6mA!

Notice: Before measuring capacitance , the capacitor must be discharged , otherwise very likely damage the meter . Expansion function.(via menu selection, ) After the display turn off automatically, press the TEST key about 1S, the menu will appear. 1. You can generate a square wave signal of 1Hz-2MHz. 2. You can generate a fixed frequency  variable pulse width wave, short key width in 1% increments, the longer the key width of 10% increments. 3. You can start a separate capacitance and ESR menu functions, ranges 2UuF-50mF, since the measurement signal amplitude is only 300mV, so the road can be measured. (Translation: Since the non-4-wire measurements, measuring lead resistance may lead to large errors, especially small ESR measurements).

Sample  pictures ***************************************************************************************** ***************************************  

Shipping
  • > We ship to worldwide.
  • > Orders processed within 24-48 hours after payment verification .
  • > We only ship to confirmed Paypal addresses. Your Paypal address MUST MATCH your Shipping address.

Country

Shipping Way

Shipping Time

Trackable

 United States

USPS(ePacket)

7-18

Yes

 Russia

China Post

15-35

Yes

 Other Country

Economic Air Mail

15-40

No

If you need register mail or other express shipping , Pls contact us.      

Warranty & Guarantee
  • > Good good quality. Buy with confidence!
  • > 14 days returned or more Guarantee. If not satisfied with the item, you can choose to return it for a replacement or money back. Please contact me before you return it. full refund after we receive our original item . Notes: the return shipping fee is paid by buyer.
  • > We maintain high standards of excellence   and strive for 100% customer satisfaction!  Positive feedback is very important to us .  We request that you contact us  BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns
   

Contact us
  • > Our goal is customer satisfaction!
  • > Our Working-time From 8:30 AM to 21:30 PM(GMT+08) .
  • > We strive to provide you with the best service, we will reply your question within 24 hours. ( IF have any problem, we will appreciate that you contact us first BEFORE open a dispute or request, we will try our best to solve the problem with you. )
   

Payment
  • > We accept Paypal only, It is fast, easy and safe.
  • > Payment must be completed within 7 days .
  • > PLEASE NOTE: S&H DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES.
   

About me      Welcome to hylbuy store! We provide many kinds electronic products and other products, such as 3D printer parts, mobile phone and tablet and laptop accessory, test equipment, pump and motor, control and convert module, music and Hi-Fi, CNC parts, DIY kits and so on. We strive for provides good product and better service. We also provide bulk price for our customers. Thanks for your support and purchase.  

    
  • Condition: New
  • Brand: Component Tester
  • Model: Component Meter
  • MPN: 15HB0602002
  • Country/Region of Manufacture: China
  • Test/Measurement Functions: Capacitance, Inductance
  • UPC: 614395000134

PicClick Insights - LCR All-in-1 Component Tester Transistor Diode Capacitance ESR Meter Inductance PicClick Exclusive

  •  Popularity - 203 watchers, 0.2 new watchers per day, 1,233 days for sale on eBay. Super high amount watching. 446 sold, 0 available.
  •  Best Price -
  •  Seller - 59,748+ items sold. 0% negative feedback. Good seller with good positive feedback and good amount of ratings.

People Also Loved PicClick Exclusive