Ships to: Americas, Europe, Asia, AU,
Item:322524444671Automatic Transfer Switch Control Module Description The configurable Automatic Transfer Switch Model ATS105SP allows many of the industry’s demanding specifications to be achieved. The ATS105SP is used to start a generator on a mains outage, sending a signal to the Auto Start Enabled Generator and transfers the load when engine’s operating criteria has been met. The engine's warm-up time before accepting load and cool-down time after relieving load can be set directly on the module (by linking pins 5,6,7,8 and battery negative pins 9,10,11,12).The ATS105SP allows working on 3 phase and single phase mains/generator supply. Each phase is monitored individually. How it works Under normal circumstances when mains power is available, National Grid power supply runs through the Automatic Transfer Switch (ATS) contactors* and connects to your distribution board. When mains power fails, the ATS will pause for a 25 sec. period to ensure you haven’t had a power spike. ATS will then initiate a generator start signal (by closing terminals 3 and 4), warm up the generator within preset time set by internal programmable timer* (see table A in PDF manual below) and then connect the generator power supply to your home or business premises. Upon mains power being restored and stays healthy for more than 25 sec. the reverse happens and the controller automatically transfers load from the generator power back to mains shutting down the generator after a cool-down period (cool-down period = warm-up period) and restoring it to standby mode. The ATS105SP series modules have been designed for front panel mounting. The module is fitted into the cut-out (68X68mm) with the fixing clips removed. These are then fitted from the rear. Download PDF Manual: https://drive.google.com/open?id=1M-b-ichadCH3eQO3OuG6AR-xtgVAv0ss Wiring Diagrams Table "A" Internal Programmable Time Delay SettingsT1 Pin 8 T2 Pin 7 T3 Pin 6 T4 Pin 5 Delay Time(sec)✓ ✓✓ 8 15✓ 25 ✓✓✓ 32 ✓ 50✓✓✓✓55✓ ✓ 70 ✓ 95✓ ✓ 120 ✓✓ 140✓✓✓ 165 ✓190✓ ✓210 ✓ ✓ 235 ✓✓ ✓260 ✓✓280 Example: to set up 140 sec. (warm-up/cool-down) delay time link pin 6 & pin 7 to the battery negative (pins 9,10,11,12 are all negative).Pins 8 & 5 are left unused. "✓" Terminal connected to batt. –ve Specification DC Supply: 12VDCMax. Operating Current: 80 mA at 12VMax. Standby Current: 10 mA at 12 VAlternator/Mains Input Range: 100 - 300 V ACFrequencies supported: 50Hz and 60HzMains/Generator Contactor Relay output:10 Amp at 250V ACGenerator Start Volt Free Relay output: 2 Amp. At 28V DCDimensions: 72 X 72 X 60mmOperating Temperature Range: -30 to +70°C2 X side clamps for secure panel fixing included. What is in the package: 1 X ATS105SP control module2 X side clamps1 X Manual: https://drive.google.com/open?id=1M-b-ichadCH3eQO3OuG6AR-xtgVAv0ss *Important note: Contactors (external relays) and other related items (fuses, cables, wires, interlocks etc) not included. You are purchasing ATS105SP control module only. We have a wide range of contactors (any size, 3 and 4 pole) available. Please send us your inquiry.Condition:New, Country/Region of Manufacture:United Kingdom, MPN:ATS105SP, Brand:GenControl
PicClick Insights for "
Automatic Transfer Switch Controller between mains and generator. AUTO start