Seller:bandsawbladesgardnergrindingservices✉️(1,045)100%,
Location:North Shields, GB,
Ships to: GB & many other countries,
Item:173874235443138" (3505mm) x 3/8" Starrett Woodpecker 4 hook. Quality bandsaw blade.
138" (11'6" - 3505mm) x 3/8" Woodpecker Premium 4 hook (T.P.I) Bandsaw blade. Starrett Woodpecker Premium 3/8" (10mm) x .022" (0.55mm) Woodpecker Premium band
saw blades are designed for all types of wood cutting including
contours and feature a spring tempered high carbon steel blade with
induction re-hardened teeth, providing decreased production times and a
better surface finish . Applications: All types of wood, plastic & Acrylic Also available in: Flexback is a high performance hard tooth, flexible back carbon steel bandsaw for cutting most materials including wood, plastic and non-ferrous metals . 3/8" (10mm) width x .025" (0.65mm) thickness. Take advantage of our combined postage. Request a total at checkout!! The correct tooth pitch to use depends upon: Material type Size of work piece Whether solid or a tube or thin-walled section In
general, cutting thinner materials requires a finer tooth pitch with
more teeth per inch (tpi). Cutting thicker materials requires a coarser
tooth pitch with fewer teeth per inch. A fine tooth pitch cuts more
slowly but with a better quality of cut. A coarse tooth pitch cuts more
quickly but with a rougher quality of cut. Using too fine a tooth pitch
will overheat the blade and shorten blade life. Using too coarse a tooth
pitch will stop the blade or strip teeth. Note that it may be necessary to vary the tooth pitch used up or down from the recommended value according to experience. Pitches for Wood-Cutting Thickness Tooth Pitch 6mm - 12mm 8tpi 12mm - 20mm 6tpi 20mm - 30mm 4tpi Over 30mm 3tpi Pitches for Metal-Cutting of Solid Sections Optimum
tooth pitches for metal-cutting vary considerably depending on the
hardness and toughness of the metal. The recommended pitches shown below
are for solid sections of mild steel. They should be increased (finer
pitch) for tough materials such as stainless steel and decreased
(coarser pitch) for soft materials such as aluminium. See the cutting
chart for more specific recommended tooth pitches for different
materials. Thickness Tooth Pitch Up to 6mm 18tpi or 14/18vp 6mm - 12mm 14tpi or 8/12vp 12mm - 25mm 10tpi or 6/10vp 25mm - 75mm 6tpi or 4/6vp 75mm - 125mm 4tpi or 3/4vp 125mm - 200mm 3tpi or 2/3vp Please look at our other bandsaw & sharpening services.. Carbon Flex Bandsaw blades made to order.. Flexback is a high performance hard tooth, flexible back carbon steel bandsaw for cutting most materials including wood, plastic and non-ferrous metals . Available in an extensive range of width, thickness, tooth pitch configurations and set patterns. Blade
length is dependent on the band saw machine being used, To establish
correct blade length, width and tooth pitch please refer to your bandsaw
manual or if in doubt contact North Easst Grinding Ltd for help and advice. Flexback is a high performance hard tooth, flexible back carbon steel bandsaw for cutting most materials including wood, plastic and non-ferrous metals Bimetal Matrix (M31/M2) are ideal general purpose metal cutting
and contour cutting of tubing, structures and solids, especially in
fabrication applications or where the material is prone to vibration. Bimetal M42 blades are used for faster or higher volume production cutting of solid and exotic or tool steels. As well as suppling quality bandsaw blades we also offer a comprehensive sharpening service for all types of saws, cutters
and DIY tools.
Please look at our sharpening service!! Our knowledge of grinding and modern grinding
machines helps us to give saws and cutters a superior cutting edge.
At North East Grinding Ltd, we know how to grind saws and cutters,
so we can give you a wear resistant edge that will last longer. Our
wide variety of grinding machines allows us to sharpen saws and cutting
tools matched to new tolerances at a competitive price. We give every
piece we sharpen the personal touch based upon the condition and use of
the item being sharpened. For further details, please contact: North East Grinding Ltd Unit 1, The Old Maltings Tanners Bank North Shields Tyne & Wear NE30 1JH