|
Package Contents:
(1) Frontier Pro with
Miraguard Antimicrobial Technology
(1) 28mm Thread/Tube Adapter
(1) 7.75" Draw Tube
(4) Replacement Prefilters
(1) Storage Pouch
(1) Operation Instructions
From the manufacturer:
The Frontier Pro™ ultralight water filter
provides all the benefits of a larger bottle filter in a compact size.
Straw style filter attaches directly to water bottles or bladders and
attached cap keeps mouthpiece clean. Flexible “Integrated Strap Grip”
secures cap to filter when not in use and allows for easy cap removal.
Bite valve can also be removed to use as hanging drip filter. Replacement
pre-filters lengthen filter life. Filters up to 50 gallons.
• Antimicrobial
• Removes Giardia, Cryptosporidium and E. Coli
• Ultralight and Compact
• Portable and Easy to Use
• No Wait Time
Use the Frontier Pro filter
to drink from any water bottle, cup, hydration system or directly from
water source. The Frontier Pro filter will remove 99.9% of Giardia,
Cryptosporidium and other contaminants down to 3µm. Activated Carbon
helps reduce waterborne chemicals and improves the taste of filtered
water. Miraguard™ Antimicrobial technology suppresses the growth of
bacteria, algae, fungus, mold and mildew within the filter media.
If viruses or smaller bacteria are suspected, use in conjunction with
Aquamira Water Purifier Tablets.
Before Initial Use:
To remove harmless carbon
dust on initial use:
1) Attach filter to water container as shown on front of package insert.
2) Pull on cap strap and position the cap to the side of the filter.
3) Pinch Bite Me™ Valve between thumb and forefinger and squeeze water
container to force water through the filter and out the valve. When the
water stream is clear, the filter is ready for use.
NOTE: Flow rates may be slightly reduced and suction a little difficult,
on initial use due to entrapped air in the filter matrix. Flow rates will
improve as the filter media becomes thoroughly wetted.
Easy to Use:
1) Attach to water container as shown on front of package insert.
2) Pull on Cap Strap and position cap to the side of the filter casing.
3) Bite on valve and suck to draw water through the filter.
To Remove/Replace Prefilter Pellet:
1) Screw off Prefilter Adapter from the base of the filter casing (Fig
1).
2) Pull the prefilter pellet out of the adapter cup (Fig 2).
3) Place a new prefilter pellet into the adapter cup (Fig 3).
4) Screw the Prefilter Adapter snuggly onto the base of the filter casing.
To Remove/Replace Bite Me™ valve:
1) Using your thumb and or forefinger, push up from the base of the sheath
to remove the sheath from the valve (Fig 4).
2) Once the sheath is removed pull on the core insert to remove it from
the boss (Fig 5).
3) The filter is now ready to be used in a gravity flow/drip system.
4) To replace Bite Me™ Valve, press the core insert into the boss until it
bottoms out on the rim of the boss.
5) Wet the inside surface of the sheath and press it over the insert and
boss until it bottoms out at the base of the boss.
6) Position the sealing rim of the sheath so that the “button” protrudes
slightly above the rim of the sheath.
To Set up a Gravity Flow “Drip”
System:
1) Remove the Bite Me valve.
2) Attach Frontier Pro to reservoir.
3) Hang the reservoir with the filter at the lowest point and allow
gravity to force water through the filter.
4) Increased distance between the reservoir and the filter will improve
drip rate.
To store filter for extended periods:
1) Remove and discard the prefilter pellet.
2) Remove Cap and Bite Me™ valve sheath
3) Allow to air dry at room temp. (Min. 48 hours)
4) Insert a new prefilter pellet prior to next use.
DO NOT FREEZE. Freezing a wetted
filter may damage the filter media and compromise filter integrity.
Color
of unit may vary. If you desire a certain color please let us know.
Thank you.
|
